CRI - Corrosion Rust Inhibitor
CRI - Corrosion Rust Inhibitor
CRI - Corrosion Rust Inhibitor
CRI - Corrosion Rust Inhibitor
  • Load image into Gallery viewer, CRI - Corrosion Rust Inhibitor
  • Load image into Gallery viewer, CRI - Corrosion Rust Inhibitor
  • Load image into Gallery viewer, CRI - Corrosion Rust Inhibitor
  • Load image into Gallery viewer, CRI - Corrosion Rust Inhibitor

CRI - Corrosion Rust Inhibitor

Regular price
$36.00
Sale price
$36.00
Regular price
Sold out
Unit price
per 

  • INFO
  • DIRECTIONS
  • SAFETY

Royal Flush Family

 

ENHANCED COOLANT ANALYSIS

GET TESTED

 

Our chemicals have been specifically formulated and developed for industrial engines and cooling systems in oil & gas, pipeline compression, locomotive, power plants, and marine industries.

Internal

 

CRI - Corrosion Rust Inhibitor

  • CRI is designed and formulated to separate corrosion & rust from your entire cooling system.
  • Prohibits rust buildup/deposits without rodding, high pressure lancing, or soaking in a hot vat offsite.
  • Maintains your cooling system back to a normal operating level.
  • Commissioning a new unit initially with CRI, will ensure a rust-free, zero-hour cooling system.
  • Get the most hours out of your systems with less downtime.


 Executive Summary

Rust Inhibitor performance is demonstrated by Dynamic Scale Loop Testing.

Test methods utilized, and results obtained are discussed below.

The best technical performance evaluations are presented in this report.

Evaluation of this data proves effectiveness and ensures the best economically solution.

 

Corrosion Wheel Testing Test Method

 

The procedure utilized in the wheel box testing is as follows:

  1. Testing uses 1018 carbon steel coupons.
  2. Coupons are washed in xylene for 2 minutes.
  3. Coupons are washed in methanol for 2 minutes.
  4. With gloved hands, wipe coupons with “kimwipes”. Dry for 15 minutes.
  5. Determine Initial Weight for each coupon.
  6. Label each container to be used.
  7. Prep water and oil with desired amounts of CO2 and H2S (Sodium Sulfide).
  8. Pour desired ratio of oil and water into bottles.
  9. Inject chemical into bottles.
  10. Set bottles in wheel apparatus.
  11. Set temperature to desired setting.
  12. Set RPM to desired speed.
  13. After desired run time, remove coupons. Rinse with xylene to remove oil.
  14. With gloved hands, scrub coupon lightly with an SOS pad.
  15. Rinse with tap water and wipe clean.
  16. Let coupon air dry.
  17. Place in bead blaster for 8 minutes.
  18. Determine Final Weight for each coupon and calculate corrosion rate.


Results

Synthetic brine was used based on the analysis of a water sample provide. Target composition of the water is shown in a table below. The testing utilized a 75% water and 25% ethylene glycol. Headspace was flushed with clean compressed air to ensure an aerobic environment. A sample was left untreated to be used as a Blank control sample for the water. The test duration of these runs were 96 hours at 180°F.

 

Continuous treatments were dosed at the listed rate for the full run time.

Pictures of the coupons were taken after the designated run period; before cleaning and after cleaning. Test data and pictures are provided below.

Target Brine Composition (mg/L)
Corrosion Data
Coupons after Test Phase – Before Cleaning

 
 

Coupons after Test Phase – After Cleaning


Conclusion 

Testing shows oxidation on the surface of the untreated coupon. On the treated coupon at 3% minimal oxidation is seen as speckling near the center of the coupon. At the 4% test point almost all of the oxidation on the surface is no longer present. No oxidation was seen on the surface of the 5% or 6% coupons. Based on weight lost during the testing period the 4% performs just under the typical threshold of 90% protection for weight loss. Increasing up to the 6% concentration provides near complete inhibition of corrosive effects.

2% - 4% - 6% Application

 

DILUTION

Ready To Use
 

Ultimate Chemicals

CRI - Corrosion Rust Inhibitor

 

For 25% Ethylene Glycol - 75% Water

6% solution suggested


For 50% Ethylene Glycol - 50% Water

3% solution suggested

 CRI - Corrosion Rust Inhibitor - SDS

 

All SDS